1991 User Manual

This manual is how to install Clear Door Edge Film in 2012 Honda Fit. You can find about how to installation, removal, repair manual other for your car.
Installing the Front Door Edge Film
1. Open the left front door. Using an alcohol swab, thoroughly clean the area where the left front door edge film will attach.
2. Close the left front door. Using a spray bottle with 3M protective tape application solution, spray the area where the left front door edge film will attach. NOTE: Do not spray the inside surface of the door.
3. Open the left front door again. Peel back about 50 mm (2 in.) of adhesive backing from the left front door edge film. Align the V-notch in the door edge film with the end of the character line on the upper part of the front door.
4. Continue to remove the adhesive backing while you align the center line on the door edge film with the edge of the door.
5. Insert the applicator into the soft sleeve. Starting in the middle of the door edge film and working outward, use the applicator to smooth out any bubbles in the film. To avoid lifting the film, move the applicator in only one direction.
6. When you are satisfied that the door edge film is firmly attached to the door, slowly remove the outer protective film.
7. Starting in the middle of the door edge film and working outward, fold the left front door edge film around the door edge using your fingers. Move your fingers in one direction. Attach the film over the seam sealant. Do not trim or damage the seam sealant.
8. Using a lint-free shop towel, wipe up the liquid from the front door edge film. Allow the front door edge film to dry thoroughly.

Installation Manual here

1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons.
2. Disconnect the negative cable from the battery.
3. Remove the front bumper. • Remove the four clips from the top of the bumper. • Remove the six clips and two self-tapping screws from the bottom of the bumper. • Remove the two self-tapping screws from both ends of the bumper. • Pull out on both ends of the bumper to release the clips, then pull the bumper forward enough that you can reach behind it and disconnect the side marker lights.
4. Using scissors, cut out template A, and place it on the bumper grille by aligning the upper edge with the left upper edge of the bumper grille as shown. Tape the template. Using a pushpin, mark the bumper grille as indicated on the template.
5. Cut out template B, and tape it onto the bumper grille by aligning the lower edge with the left lower edge of the bumper grille as shown. Using a pushpin, mark the bumper grille as indicated on the template.

Download here

Installation Summary for 2006 Honda Civic Air Conditioner Installation Manual
1. Write down the radio station presets.
2. With the ignition switch on, turn on the windshield wipers. When the wipers reach the top position turn off the ignition switch.
3. Disconnect the negative cable from the battery.
4. Inside the passenger’s compartment, remove the passenger dashboard undercover and then the glove box (two 8 mm washer-bolts for the hinges, then open the glove box to remove).
5. Remove the steel glove box lower frame (two washer-bolts.
6. Using diagonal cutters (and/or a utility knife), cut out the dashboard-link at the glove box area.
7. Remove the passenger’s heater duct (one hex screw and two self-tapping screws), and remove the harness connector clip.

We found this information in search engine is available on the internet. None of those materials are hosted in this server nor uploaded by me in someone’s servers. Read our DISCLAIMER for more detail.

2006 Honda Civic Air Conditioner here

Installation Summary apply for 2012 Honda Fit :
1. Open the tailgate. Install the three loops on the center cargo liner under the rear seat headrests.
2. Pull the knobs and fold down the left and right seat-backs. Position the center cargo liner on the left and right seat-backs. Secure the center cargo liner to the left and right seat-backs with 10 hook-and-loop fasteners.
3. Position the center cargo liner on the cargo area floor. Secure the center cargo liner to the cargo area floor with six hook-and-loop fasteners.
4. Lift the cargo area floor. Install the two straps on the center cargo liner around the edge of the cargo area floor.
5. Lower the cargo area floor.
6. Position the center cargo liner on the cargo area floor. Fold over the rear corners. Using an alcohol swab, clean the areas where the fastener pads will attach.
7. Attach two fastener pads to the center cargo liner fasteners as shown.
8. Remove the adhesive backings from the two fastener pads, position the center cargo liner, and attach the two fastener pads to the cargo area floor.
Installing the Left Cargo Liner
9. Position the left cargo liner on the cargo area left side trim panel. Fold back the edge of the left cargo liner. Using an alcohol swab, clean the areas where the 13 fastener pads will attach.

download manual here

This manual is how to install Exhaust System in 2007-2008 Dodge Avenger. Installation Summary :
Exhaust System Installation
1. Place a clamp over the expanded end of the front muffler assembly and set it into position as shown in figure 3 making sure to install the hanger into the rubber isolator. Do Not tighten the clamp.
2. Place a clamp over the expanded end of the y pipe assembly and set it into position as shown in figure 4. Do Not tighten the clamp.
3. Place a clamp over the expanded end of the left rear muffler assembly and set it into position as shown in figure 5 making sure to install the hanger into the rubber isolator. Do Not tighten the clamp.
4. Clip the ground strap onto the left muffler as shown in figure 6.
5. Place a clamp over the expanded end of the right rear muffler assembly and set it into position.
6. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.
7. Once position has been determined to be correct, tighten the Accuseal clamps to 32-35 ft. lbs. making sure the clamps openings are not over any of the notches in the pipes.

2007-2008 manual here